Some secret codes and hacks for your Nokia !
Most codes work on all Nokia
..................................
Enhanced Full Rate Codec (EFR):
On: Enter *3370# and EFR will be activated after a reboot of the phone (consumes more power )
Off: Enter #3370# and EFR will be switched off after a reboot of the phone.
Half Rate Codec:
On: Enter *4720# and Half Rate coded will be activated after a reboot of the phone ( better standby time )
Off: Enter #4720# and Half Rate coded will be de-activated after a reboot of the phone.
Enhanced Full Rate will give you much better sound quality when you enable
it. the new Enhanced Full Rate CODEC adopted by GSM uses the ASELP
(AlgebraicCode Excitation Linear Prediction) compression technology.
This technology allows for much great voice quality in the same number of
bits as the older Full Rate CODEC. The older technology was called LPC-RPE
(Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13
kilobits.(but you take up more space on the network, so they can charge you
more) - Talk-time is reduced with about 5% Half Rate will give you bad
soundquality, which gives the serviceprovider the opportunity to have
more calls on the network, and you might get a lower charge from them. -
Will give you 30% longer talk-time.
----------------------------------------
Network Monitor (61xx)
This is a hidden menu in your Nokia. If you want to active it you'll have
to reprogram some chips inside of your phone. For example the Nokia 6110 Network Monitor:
1. Check your Software version. You can continue ONLY if you have 4.33, 4.73 or 5.24!
2. Take apart the phone.
3. Desolder the EEProm (ATMEL AT 24C64).
4. Read out the data with an EEProm progammer and save it to a file (backup).
5. If you have v4.33 or 4.73 then change adress 03B8 from 00 to FF.
6. If you have v5-24 then change 0378 from 00 to FF.
7. Write the new data to the EEProm and solder it back into the mobile.
8. Power on your phone and you should have menu number 10.
The Network Monitor gives you the following informations:
Carrier number
MS RX level in dBM
Received signal quality
MS TX power level
C1 (path loss criterion, used for cell selection and reselection). The range is -99 to 99
RLT (Radio Link timeout)
Timeslot
Indication of the transmitter status
Information on the network parameters
TMSI (temporary Mobile Subscriber Identity)
Cell Identification (CELL ID, number of the cell being used)
MCC (Mobile Country Code)
MNC (Mobile Network Code)
LAC (location Area Code)
Ciphering (on/off)
Hopping (on/off)
DTX (on/off)
Discarding cell barred information
----------------------------------------
Clock stopping :
(*#746025625#)
Shows whether or not your sim card supports clock stopping. Not all versions of the software will report this.
------------------------------------------
Show IMEI code (all phones):
* # 06 #
-------------------------------------------
Software Version :
This code shows you software version, date of manufacture and hardware model number of your phone.
* # 3110 #
Show warranty information
To get additional information from your phone you can use the so called
"warranty codes", try typing:
*#92702689# (= *#war0anty#).
You will be asked a 'warranty code:'
type:
6232 (OK) :
To display the Month and Year of Manufacture.
7332 (OK) :
To display the date of the last repairment.
7832 (OK) :
To display (if previously set)
the date where the phone was purchased.
9268 (OK) :
To display the Serial Number.
37832 (OK) :
To set the Purchasing Date MMYY
(Warning: You can only do this once)
87267 (OK) :
To Confirm Transfer
--------------------------------------------
To restore factory settings :
(This does not include memory, language and counters) type:
*#7780#
-------------------------------------
SPLock Mode :
If you want to ask your phone about SPlock, you can use the following:
# pw + 1234567890 + [y] #
If you put your hands on your 10 digits SPlock code yet, then you can modify the status of the above results, typeing:
# pw + [mastercode] + [y] #
where:
[y] is 1 up to 4, and
any ten digits number seems working instead of "1234567890"
Unlock SP lock
Here is a way to Unlock your phone which is Service Provider locked,
without to know SPLock code !!!!
Give it a try:
First of all, PIN CODE MUST BE ON, then press: C
C and hold until it clears display
* and hold until start to blink
* and hold until start to blink
04***your pin>#
Each time you turn your phone OFF it resets the lock,
so this need to be done each time you'll turn your phone ON
Anyway it's better than nothing, isn't it?
-----------------------------------------
Show Service Menu :
To get additional information from your phone you can use the
so called "warranty code", try typing: *#92702689#
Now you are in service menu where you'll find:
1 IMEI (International Mobile Equipment Identification)
2 Made MM/YY (date of production of the phone mm/yy)
3 Purchasing Date (here you can enter the date of purchase.
If you enter an incorrect date, you cannot correct it later !
4 Repaired (date of repair, if there was one)
5 Transfer user data?
-----------------------------------------
Profiles Menu :
If you press the "Power on"
button for a short moment, the menu with the profiles is shown on the display.
If you press one more time,
the mobile turns itself off.
You can use the up and down cursor keys to scroll and enable a different alert setting.
---------------------------------------------
Pin Out 51xx :
1 - VIN CHARGER INPUT VOLTAGE 8.4V 0.8A
2 - CHRG CTRL CHARGER CONTROL PWM 32Khz
3 - XMIC MIC INPUT 60mV - 1V
4 - SGND SIGNAL GROUND
5 - XEAR EAR OUTPUT 80mV - 1V
6 - MBUS 9600 B/S
7 - FBUS_RX 9.6 - 230.4 KB/S
8 - FBUS_TX 9.6 - 230.4 KB/S
9 - L_GND CHARGER / LOGIC GND
---------------------------------------
Pin-Out 8110 :
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
1 - Charger/System Ground
2 - Accessory Output Supply. (3.4V...10V - 50mA)
3 - External Microphone Input and Accessory Identification
*1,7...2,05 V Headset Adapter Connected
*1,15...1,4 V Compact Handsfree Unit Connected
*2.22...2.56 V Infra Red Link Conneceted
4 - External RF Control Input
*0...0.5V External RF in use
*2.4...3.2V Internal Antenna in use
5 - FBUS Transmit
6 - Serial Control Bus
*Logic Low Level: 0....0.5V
*Logic High Level:2.4V....3.2V
7 - Not Connected
8 - Signal Ground
9 - External Speaker and Mute Control
Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c.
Mute OFF (HF SPEAKER ACTIVE
1,0...1,7 V d.c.
10 - Hook Signal
*Hook Off (Handset in Use): 0....0.5V
*Hook On (Handset in Use): 2.4V....3.2V
11 - FBUS Receive
12 - Charging Supply Voltage (Max 16V)
NOKIA 9000 :
Software Version
This code shows you software version of your Communicator:
*#682371158412125#
Date of Manufacture
This code shows you the manufacturing date of your Communicator:
*#3283# (or *#DATE#)
------------------------------------------
Crazy 5110 :Send a SMS full of . (dots) the it'll go crazy when you scroll the received message in your 5110.
doesn't do any permanent damage...it only goes crazy if you scroll the SMS. 'm not sure if it works with all of the software
version but it works with 4.59. Doesn't work on SW version 4.53 ..
GSM Codes :
The following codes are the standard GSM codes for various network services. Most Nokia phones have easier ways to activate
them through the menus. Check the guides for your model.
Call Diverting
All
To Activate: * * 21 * NUMBER # [SEND]
To Cancel: # # 21 # [SEND]
To Check: * # 21 # [SEND]
No Answer
To Activate: * * 61 * NUMBER # [SEND]
To Cancel: # # 61 # [SEND]
To Check: * # 61 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER # [SEND]
To Cancel: # # 62 # [SEND]
To Check: * # 62 # [SEND]
Busy
To Activate: * * 67 * NUMBER # [SEND]
To Cancel: # # 67 # [SEND]
To Check: * # 67 # [SEND]
To Cancel All Call Forwarding # # 002 # [SEND]
Diverting Data Calls
All
To Activate: * * 21 * NUMBER * 25 # [SEND]
To Cancel: # # 21 # * 25 [SEND]
To Check Status: * # 21 # * 25 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 25 # [SEND]
To Cancel: # # 61 * 25 # [SEND]
To Check Status: * # 61 # * 25 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 25 # [SEND]
To Cancel: # # 62 # * 25 # [SEND]
To Check Status: * # 62 # * 25 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 25 # [SEND]
To Cancel: # # 67 # * 25 # [SEND]
To Check Status: * # 67 # * 24 # [SEND]
Diverting Fax Calls
All
To Activate: * * 21 * NUMBER * 13 #[SEND]
To Cancel: # # 21 # * 13 # [SEND]
To Check Status: * # 21 # * 13 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 13 # [SEND]
To Cancel: # # 61 * 13 # [SEND]
To Check Status: * # 61 # * 13 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 13 # [SEND]
To Cancel: # # 62 # * 13 # [SEND]
To Check Status: * # 62 # * 13 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 13 # [SEND]
To Cancel: # # 67 # * 13 # [SEND]
To Check Status: * # 67 # * 13 #[SEND]
Call Barring
Before you can activate these barring services you will need a barring code from your service provider.
Call Barring can not be activated if Call Forwarding diverts are already in use.
All Calls
To Activate: * 330 * BARRING CODE # [SEND]
To Cancel: # 330 * BARRING CODE # [SEND]
To Check: * # 330 # [SEND]
All Outgoing Calls
To Activate: * 333 * BARRING CODE # [SEND]
To Cancel: # 333 * BARRING CODE # [SEND]
To Check: * # 333 # [SEND]
All Incoming Calls
To Activate: * 353 * BARRING CODE # [SEND]
To Cancel: # 353 * BARRING CODE # [SEND]
To Check: * # 353 # [SEND]
All Outgoing Calls
To Activate: * 33 * BARRING CODE# [SEND]
To Cancel: # 33 * BARRING CODE # [SEND]
To Check: * # 33 # [SEND]
All Outgoing International Calls
To Activate: * 331 * BARRING CODE# [SEND]
To Cancel: # 331 * BARRING CODE # [SEND]
To Check: * # 331 # [SEND]
All Outgoing International Calls Except To Home Country
To Activate: * 332 * BARRING CODE# [SEND]
To Cancel: # 332 * BARRING CODE # [SEND]
To Check: * # 332 # [SEND]
All Incoming Calls
To Activate: * 35 * BARRING CODE # [SEND]
To Cancel: # 35 * BARRING CODE # [SEND]
To Check: * # 35 # [SEND]
All Incoming Calls When Outside Home Country
To Activate: * 351 * BARRING CODE # [SEND]
To Cancel: # 351 * BARRING CODE # [SEND]
To Check: * # 351 # [SEND]
Canceling All Call Barring # 330 * BARRING CODE # [SEND]
Call Waiting
To Activate: * 43 # [SEND]
To Deactivate: # 43 # [SEND]
To Check: * # 43 # [SEND]
Calling Line Identity
Outgoing
To Activate: * 31 # [SEND]
To Deactivate: # 31 # [SEND]
To Check: * # 31 # [SEND]
Incoming
To Activate: * 30 # [SEND]
To Deactivate: # 30 # [SEND]
--------------------------------------------
SMS Secrets :
Cell Broadcasting
While Short Message Service (SMS) can be configured as a personal service, Cell Broadcast is a general
service which is designed for subscribers of a specific cell or topic. For example, a subscriber
to cell 050 in England will receive information on the GSM tower currently being used by their phone. This new
concept brings a whole new meaning to the term mobile communications as the phone is now able to receive
information such as share prices or weather updates without the need of data cards and computers. At
present the following message types exist (note: this may vary from carrier to carrier and some carriers may charge
for this service):
Code Title
000 Index
010 Flashes
020 Hospitals
022 Doctors
024 Pharmacy
030 Long Distant Road Reports
032 Local Road Reports
034 Taxis
040 Weather
050 District
052 Network Information
054 Operator Services
056 Directory Inquiries (national)
057 Directory Inquiries (international)
058 Customer Care (national)
059 Customer Care (international)
IMEI Info :
This will clarify what your IMEI no means
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type Approval Code (first 2 digits = country code of the approval-country )
FAC = Final Assembly Code (01,02 = AEG)
(10,20 Nokia)
(40,41,44 Siemens)
(30 Ericsson)
(50 Bosch)
(51 Sony,Siemens,Ericsson)
(60 Alcatel)
(65 AEG)
(70 Sagem)
(75 Dancall)
(80 Philips)
(85 Panasonic)
SNR = Serial Nr.
SP = Spare (always "0")
----------------------------------
May be out of date now !!!!
Latest software versions:
Nokia 1610 NHE-5NX 5,23
Nokia 1611 NHE-5SX 4,05
Nokia 2010 NHE-3 5,12
Nokia 2110 NHE-1 4,97m
Nokia 2110i/2118 NHE-4 5,70
Nokia 3110 NHE-8 8,50
Nokia 3210 NSE-8/9 5,01
Nokia 5110 NSE-1 5,24
Nokia 6080 NME-2 4,80
Nokia 6081 NME-2A 5,14
Nokia 6090 NSM-3 4,10
Nokia 6110 NSE-3 5,48
Nokia 6150 NSM-1 5,22
Nokia 7110 NSE-5 4,76
Nokia 8110 NHE-6BX 6,21
Nokia 8110i NHE-6BM 5,20
Nokia 8210 NSM-3 5,11
Nokia 8810 NSE-6 5,00
Nokia 8850 NSM-2 5,11
Nokia 9110 RAE-2 5,02 / 4,15
AL MASEER
Most codes work on all Nokia
..................................
Enhanced Full Rate Codec (EFR):
On: Enter *3370# and EFR will be activated after a reboot of the phone (consumes more power )
Off: Enter #3370# and EFR will be switched off after a reboot of the phone.
Half Rate Codec:
On: Enter *4720# and Half Rate coded will be activated after a reboot of the phone ( better standby time )
Off: Enter #4720# and Half Rate coded will be de-activated after a reboot of the phone.
Enhanced Full Rate will give you much better sound quality when you enable
it. the new Enhanced Full Rate CODEC adopted by GSM uses the ASELP
(AlgebraicCode Excitation Linear Prediction) compression technology.
This technology allows for much great voice quality in the same number of
bits as the older Full Rate CODEC. The older technology was called LPC-RPE
(Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13
kilobits.(but you take up more space on the network, so they can charge you
more) - Talk-time is reduced with about 5% Half Rate will give you bad
soundquality, which gives the serviceprovider the opportunity to have
more calls on the network, and you might get a lower charge from them. -
Will give you 30% longer talk-time.
----------------------------------------
Network Monitor (61xx)
This is a hidden menu in your Nokia. If you want to active it you'll have
to reprogram some chips inside of your phone. For example the Nokia 6110 Network Monitor:
1. Check your Software version. You can continue ONLY if you have 4.33, 4.73 or 5.24!
2. Take apart the phone.
3. Desolder the EEProm (ATMEL AT 24C64).
4. Read out the data with an EEProm progammer and save it to a file (backup).
5. If you have v4.33 or 4.73 then change adress 03B8 from 00 to FF.
6. If you have v5-24 then change 0378 from 00 to FF.
7. Write the new data to the EEProm and solder it back into the mobile.
8. Power on your phone and you should have menu number 10.
The Network Monitor gives you the following informations:
Carrier number
MS RX level in dBM
Received signal quality
MS TX power level
C1 (path loss criterion, used for cell selection and reselection). The range is -99 to 99
RLT (Radio Link timeout)
Timeslot
Indication of the transmitter status
Information on the network parameters
TMSI (temporary Mobile Subscriber Identity)
Cell Identification (CELL ID, number of the cell being used)
MCC (Mobile Country Code)
MNC (Mobile Network Code)
LAC (location Area Code)
Ciphering (on/off)
Hopping (on/off)
DTX (on/off)
Discarding cell barred information
----------------------------------------
Clock stopping :
(*#746025625#)
Shows whether or not your sim card supports clock stopping. Not all versions of the software will report this.
------------------------------------------
Show IMEI code (all phones):
* # 06 #
-------------------------------------------
Software Version :
This code shows you software version, date of manufacture and hardware model number of your phone.
* # 3110 #
Show warranty information
To get additional information from your phone you can use the so called
"warranty codes", try typing:
*#92702689# (= *#war0anty#).
You will be asked a 'warranty code:'
type:
6232 (OK) :
To display the Month and Year of Manufacture.
7332 (OK) :
To display the date of the last repairment.
7832 (OK) :
To display (if previously set)
the date where the phone was purchased.
9268 (OK) :
To display the Serial Number.
37832 (OK) :
To set the Purchasing Date MMYY
(Warning: You can only do this once)
87267 (OK) :
To Confirm Transfer
--------------------------------------------
To restore factory settings :
(This does not include memory, language and counters) type:
*#7780#
-------------------------------------
SPLock Mode :
If you want to ask your phone about SPlock, you can use the following:
# pw + 1234567890 + [y] #
If you put your hands on your 10 digits SPlock code yet, then you can modify the status of the above results, typeing:
# pw + [mastercode] + [y] #
where:
[y] is 1 up to 4, and
any ten digits number seems working instead of "1234567890"
Unlock SP lock
Here is a way to Unlock your phone which is Service Provider locked,
without to know SPLock code !!!!
Give it a try:
First of all, PIN CODE MUST BE ON, then press: C
C and hold until it clears display
* and hold until start to blink
* and hold until start to blink
04***your pin>#
Each time you turn your phone OFF it resets the lock,
so this need to be done each time you'll turn your phone ON
Anyway it's better than nothing, isn't it?
-----------------------------------------
Show Service Menu :
To get additional information from your phone you can use the
so called "warranty code", try typing: *#92702689#
Now you are in service menu where you'll find:
1 IMEI (International Mobile Equipment Identification)
2 Made MM/YY (date of production of the phone mm/yy)
3 Purchasing Date (here you can enter the date of purchase.
If you enter an incorrect date, you cannot correct it later !
4 Repaired (date of repair, if there was one)
5 Transfer user data?
-----------------------------------------
Profiles Menu :
If you press the "Power on"
button for a short moment, the menu with the profiles is shown on the display.
If you press one more time,
the mobile turns itself off.
You can use the up and down cursor keys to scroll and enable a different alert setting.
---------------------------------------------
Pin Out 51xx :
1 - VIN CHARGER INPUT VOLTAGE 8.4V 0.8A
2 - CHRG CTRL CHARGER CONTROL PWM 32Khz
3 - XMIC MIC INPUT 60mV - 1V
4 - SGND SIGNAL GROUND
5 - XEAR EAR OUTPUT 80mV - 1V
6 - MBUS 9600 B/S
7 - FBUS_RX 9.6 - 230.4 KB/S
8 - FBUS_TX 9.6 - 230.4 KB/S
9 - L_GND CHARGER / LOGIC GND
---------------------------------------
Pin-Out 8110 :
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
1 - Charger/System Ground
2 - Accessory Output Supply. (3.4V...10V - 50mA)
3 - External Microphone Input and Accessory Identification
*1,7...2,05 V Headset Adapter Connected
*1,15...1,4 V Compact Handsfree Unit Connected
*2.22...2.56 V Infra Red Link Conneceted
4 - External RF Control Input
*0...0.5V External RF in use
*2.4...3.2V Internal Antenna in use
5 - FBUS Transmit
6 - Serial Control Bus
*Logic Low Level: 0....0.5V
*Logic High Level:2.4V....3.2V
7 - Not Connected
8 - Signal Ground
9 - External Speaker and Mute Control
Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c.
Mute OFF (HF SPEAKER ACTIVE
1,0...1,7 V d.c.10 - Hook Signal
*Hook Off (Handset in Use): 0....0.5V
*Hook On (Handset in Use): 2.4V....3.2V
11 - FBUS Receive
12 - Charging Supply Voltage (Max 16V)
NOKIA 9000 :
Software Version
This code shows you software version of your Communicator:
*#682371158412125#
Date of Manufacture
This code shows you the manufacturing date of your Communicator:
*#3283# (or *#DATE#)
------------------------------------------
Crazy 5110 :Send a SMS full of . (dots) the it'll go crazy when you scroll the received message in your 5110.
doesn't do any permanent damage...it only goes crazy if you scroll the SMS. 'm not sure if it works with all of the software
version but it works with 4.59. Doesn't work on SW version 4.53 ..
GSM Codes :
The following codes are the standard GSM codes for various network services. Most Nokia phones have easier ways to activate
them through the menus. Check the guides for your model.
Call Diverting
All
To Activate: * * 21 * NUMBER # [SEND]
To Cancel: # # 21 # [SEND]
To Check: * # 21 # [SEND]
No Answer
To Activate: * * 61 * NUMBER # [SEND]
To Cancel: # # 61 # [SEND]
To Check: * # 61 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER # [SEND]
To Cancel: # # 62 # [SEND]
To Check: * # 62 # [SEND]
Busy
To Activate: * * 67 * NUMBER # [SEND]
To Cancel: # # 67 # [SEND]
To Check: * # 67 # [SEND]
To Cancel All Call Forwarding # # 002 # [SEND]
Diverting Data Calls
All
To Activate: * * 21 * NUMBER * 25 # [SEND]
To Cancel: # # 21 # * 25 [SEND]
To Check Status: * # 21 # * 25 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 25 # [SEND]
To Cancel: # # 61 * 25 # [SEND]
To Check Status: * # 61 # * 25 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 25 # [SEND]
To Cancel: # # 62 # * 25 # [SEND]
To Check Status: * # 62 # * 25 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 25 # [SEND]
To Cancel: # # 67 # * 25 # [SEND]
To Check Status: * # 67 # * 24 # [SEND]
Diverting Fax Calls
All
To Activate: * * 21 * NUMBER * 13 #[SEND]
To Cancel: # # 21 # * 13 # [SEND]
To Check Status: * # 21 # * 13 # [SEND]
No Answer
To Activate: * * 61 * NUMBER * 13 # [SEND]
To Cancel: # # 61 * 13 # [SEND]
To Check Status: * # 61 # * 13 # [SEND]
Unreachable
To Activate: * * 62 * NUMBER * 13 # [SEND]
To Cancel: # # 62 # * 13 # [SEND]
To Check Status: * # 62 # * 13 # [SEND]
Busy
To Activate: * * 67 * NUMBER * 13 # [SEND]
To Cancel: # # 67 # * 13 # [SEND]
To Check Status: * # 67 # * 13 #[SEND]
Call Barring
Before you can activate these barring services you will need a barring code from your service provider.
Call Barring can not be activated if Call Forwarding diverts are already in use.
All Calls
To Activate: * 330 * BARRING CODE # [SEND]
To Cancel: # 330 * BARRING CODE # [SEND]
To Check: * # 330 # [SEND]
All Outgoing Calls
To Activate: * 333 * BARRING CODE # [SEND]
To Cancel: # 333 * BARRING CODE # [SEND]
To Check: * # 333 # [SEND]
All Incoming Calls
To Activate: * 353 * BARRING CODE # [SEND]
To Cancel: # 353 * BARRING CODE # [SEND]
To Check: * # 353 # [SEND]
All Outgoing Calls
To Activate: * 33 * BARRING CODE# [SEND]
To Cancel: # 33 * BARRING CODE # [SEND]
To Check: * # 33 # [SEND]
All Outgoing International Calls
To Activate: * 331 * BARRING CODE# [SEND]
To Cancel: # 331 * BARRING CODE # [SEND]
To Check: * # 331 # [SEND]
All Outgoing International Calls Except To Home Country
To Activate: * 332 * BARRING CODE# [SEND]
To Cancel: # 332 * BARRING CODE # [SEND]
To Check: * # 332 # [SEND]
All Incoming Calls
To Activate: * 35 * BARRING CODE # [SEND]
To Cancel: # 35 * BARRING CODE # [SEND]
To Check: * # 35 # [SEND]
All Incoming Calls When Outside Home Country
To Activate: * 351 * BARRING CODE # [SEND]
To Cancel: # 351 * BARRING CODE # [SEND]
To Check: * # 351 # [SEND]
Canceling All Call Barring # 330 * BARRING CODE # [SEND]
Call Waiting
To Activate: * 43 # [SEND]
To Deactivate: # 43 # [SEND]
To Check: * # 43 # [SEND]
Calling Line Identity
Outgoing
To Activate: * 31 # [SEND]
To Deactivate: # 31 # [SEND]
To Check: * # 31 # [SEND]
Incoming
To Activate: * 30 # [SEND]
To Deactivate: # 30 # [SEND]
--------------------------------------------
SMS Secrets :
Cell Broadcasting
While Short Message Service (SMS) can be configured as a personal service, Cell Broadcast is a general
service which is designed for subscribers of a specific cell or topic. For example, a subscriber
to cell 050 in England will receive information on the GSM tower currently being used by their phone. This new
concept brings a whole new meaning to the term mobile communications as the phone is now able to receive
information such as share prices or weather updates without the need of data cards and computers. At
present the following message types exist (note: this may vary from carrier to carrier and some carriers may charge
for this service):
Code Title
000 Index
010 Flashes
020 Hospitals
022 Doctors
024 Pharmacy
030 Long Distant Road Reports
032 Local Road Reports
034 Taxis
040 Weather
050 District
052 Network Information
054 Operator Services
056 Directory Inquiries (national)
057 Directory Inquiries (international)
058 Customer Care (national)
059 Customer Care (international)
IMEI Info :
This will clarify what your IMEI no means
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type Approval Code (first 2 digits = country code of the approval-country )
FAC = Final Assembly Code (01,02 = AEG)
(10,20 Nokia)
(40,41,44 Siemens)
(30 Ericsson)
(50 Bosch)
(51 Sony,Siemens,Ericsson)
(60 Alcatel)
(65 AEG)
(70 Sagem)
(75 Dancall)
(80 Philips)
(85 Panasonic)
SNR = Serial Nr.
SP = Spare (always "0")
----------------------------------
May be out of date now !!!!
Latest software versions:
Nokia 1610 NHE-5NX 5,23
Nokia 1611 NHE-5SX 4,05
Nokia 2010 NHE-3 5,12
Nokia 2110 NHE-1 4,97m
Nokia 2110i/2118 NHE-4 5,70
Nokia 3110 NHE-8 8,50
Nokia 3210 NSE-8/9 5,01
Nokia 5110 NSE-1 5,24
Nokia 6080 NME-2 4,80
Nokia 6081 NME-2A 5,14
Nokia 6090 NSM-3 4,10
Nokia 6110 NSE-3 5,48
Nokia 6150 NSM-1 5,22
Nokia 7110 NSE-5 4,76
Nokia 8110 NHE-6BX 6,21
Nokia 8110i NHE-6BM 5,20
Nokia 8210 NSM-3 5,11
Nokia 8810 NSE-6 5,00
Nokia 8850 NSM-2 5,11
Nokia 9110 RAE-2 5,02 / 4,15
AL MASEER
: 
: 
: