لقد قمت بترقيت ال Bios باستخدام برنامج Award Flash وبعد طبعا ان نزلت ملف تمت العملية بنجاح لكن بعد اعادة تشغيل الجهاز لم فشل الجهاز في التشغيل .

هل هناك حل لهذه المشكلة؟؟؟؟


طبعا اتبعت التعليمات التالية:

AwardBIOS Part Number: 2y69KD13

Copyright (c) 2002, Award Software International, Inc. award.com
Copyright (c) 2002, eSupport.com, Inc. eSupport.com
------------------------------------------------------------------------------
The System BIOS file contains an AwardBIOS customized for your motherboard.

Unlike most programs that you are familiar with, the System BIOS does not
execute from disk. Instead, it is stored in a Flash-ROM component that
resides on the motherboard and begins executing immediately upon powerup.
This Flash-ROM can be reprogrammed by means of a Flash Upload Utility. In
order to install AwardBIOS (r) in your computer, you'll need to reprogram
its Flash-ROM through use of the Flash Loader utility.

BE ADVISED THAT THERE IS AN ELEMENT OF RISK IN REPROGRAMMING THE COMPUTER'S
FLASH SYSTEM BIOS. If the Flash Load procedure begins, but fails to completely
load a valid BIOS image, your computer will be out of commission and you may
have to have it serviced. If while loading AwardBIOS onto your computer you
experience a failure, and if your computer has a recovery mode, you should set
it and refer to the instructions for restoring the original bios that came
with the computer. The Flash-ROM will need to be physically replaced with
another that contains valid code. Reasons for the Flash Upload failure
include: 1) losing power while the upload is in progress, and 2) specifying
and uploading the wrong file. Needless to say, this would be a horribly
disappointing experience. Unicore Software Inc. would most sincerely regret
such a misfortune, however, understand that eSupport.com INC. DISCLAIMS
ALL RESPONSIBILITY AND LIABILITY FOR THE USE AND CONSEQUENCES OF THE USE OF
THIS PRODUCT. So, please, take your time and be careful!

The Flash Loader contains 2 basic steps for installing a new BIOS. First it
asks for the filename containing the new BIOS to be installed. It then asks
whether you want to save a backup copy of the current BIOS installed.

Be sure to backup the original BIOS before uploading AwardBIOS into the
Flash-ROM. Otherwise, you won't be able to uninstall AwardBIOS should you
want to do so. Even if you're sure you won't, it is a good practice to
retain all original equipment that is supplied with your computer, "just in
case".

The exact steps for uploading AwardBIOS are enumerated in the Instructions
section below. Assuming you have followed those instructions and the upload
has just completed, the Flash Loader will display a message directing you to
reset the computer or re-cycle its power. Upon doing so, you will be greeted
with a message "CMOS checksum error - Defaults loaded". Don't be alarmed.
This is normal and will only occur the first time the system is booted after
installing a new BIOS. You may also find a message "Press F1 to continue, DEL
to enter SETUP". If this message is displayed it is advised that you press DEL
to enter BIOS setup and select the setup option "STANDARD CMOS SETUP" to verify
the correct time and date. Beyond that, everything else will already be set
for optimal performance and you can simply exit by pressing <F10>. Or, you
might browse around and tailor some options like Password Security or Power
Management per your preference. After this Setup session, your computer will
reboot thereafter without any hysterical messages.

------------------------------------------------------------------------------
-------------------------------------
AwardBIOS (r) Installation Instructions
-------------------------------------
WARNING: Flash upgrading your BIOS can render you system inoperative.
eSupport.com will not be responsible for users who flash upgrade their BIOS
and render their system inoperable due to the use of incorrect filenames or
file types used to program the BIOS.

Step 1
------
Turn on your computer, enter CMOS setup by pressing the delete (del) key
during the Boot Sequence, and set the first boot device to be A: (floppy)
Save settings and exit by pressing F10.

Step 2
------
Shut down the system, and then insert eSupport BIOS Flash Upgrade Disk.

Step 3
------
Reboot the system.

Step 4
------
The program will perform the flash automatically. When asked to continue or
quit, press any key to continue. Do NOT reset or turn off the computer during
the flash process or your BIOS may be damaged.

Step 5
------
When the flash is finished, you will be prompted to quit the program or
restart the system. Choose to restart the system. (Make sure that the flash
disk has been removed).

Step 6
------
Your system has now been flashed with the new eSupport BIOS upgrade. You
should see the new BIOS version displayed on the screen during bootup. Press
the Delete key to setup your BIOS again if necessary.

----------------------------
Un-Install Instructions
----------------------------

Step 1
------
Shut down the system, and then insert eSupport BIOS Flash Upgrade Disk.

Step 2
------
Reboot the system.

Step 3
------
The system will tell you that this disk has already been used to upgrade
your BIOS. Simply type "bflash original.bin" and answer "no" to save
the BIOS and "yes" to program the BIOS.

Step 4
------
When the flash is finished, it will ask you to restart or quit. Remove the
diskette from the drive and restart your computer.

------------------------------------------------------------------------------

شكرا جزيلا وجدت هذه الطريقة ونجحت والجهاز شغال اللحين بدون الحاجة للمغامرة بجهاز آخر.

Recovering a Corrupt AWARD BIOS
With AWARD BIOS the process is similar but still a bit different. To recover an AWARD BIOS you
will need to create a floppy diskette with a working BIOS file in .BIN format, an AWARD flash
utility and an AUTOEXEC.BAT file. AWARD BIOS will not automatically restore the BIOS
information to the SYSTEM BLOCK for this reason you will need to add the commands necessary
to flash the BIOS in the AUTOEXEC.BAT file. The system will run the AUTOEXE.BAT file, which
will in turn flash the BIOS. This is fairly easy. Here are the steps you need to take.
· Create a bootable floppy diskette
· Copy the BIOS file and flash utility to the diskette
· Create an text file with any standard text editor and add the following lines
@ECHO OFF
FLASH763 BIOSFILE.BIN /py
In the above example I am assuming that you are using the FLASH763.EXE flash utility. You will
need to replace the FLASH763 with the name of whatever flash utility you are using, and replace
the BIOSFILE.BIN with the name of the BIOS file you are using. You will also need to change the
‘/py’ to whatever the command is for your flash utility to automatically program the BIOS without
user intervention.
If you do not know the command to automatically flash your BIOS type the name of the flash
utility with a space and then /? to display the utility’s help screen. The help screen should specify
the command switch to automatically flash your BIOS. If you are using the FLASH763.EXE utility
then the switch to automatically flash your BIOS is ‘/py’.